Stopping on a steep gradient, remaining stationary for a moment and then pulling away safely. Situations like these reveal how well a vehicle’s brakes, drivetrain and driver assistance systems perform. That is why vehicle manufacturers need to replicate such conditions during vehicle development and testing, ideally across a range of gradients. An ordinary road, however, is not suitable for this type of testing. At the AUREL proving ground, we have the solution: test roads with eight different gradients ranging from 5% to 65%, plus one unique facility found nowhere else in the world. Let’s take a closer look at the possibilities for gradient testing.
Eight Different Gradients for Different Types of Testing
Gradient test roads are a common feature at proving grounds. However, the range of gradients available to development teams at the AUREL Proving Ground is exceptionally broad. Our test roads feature gradients of 5%, 8%, 12%, 15%, 20%, 26%, 30% and even 65%. The steepest gradient is particularly important for the development of off-road vehicles – passenger cars are not required to be tested on such a steep gradient under applicable standards.
Manufacturers use our facilities to test braking systems, parking brakes and drivetrain components, for example. They also fine-tune powertrain and chassis software, traction control systems, hill-start assist and stability control systems. Thanks to the controlled environment, tests can be repeated multiple times under identical conditions.
Under normal conditions, a vehicle manufacturer might need to cover tens of thousands of kilometres to verify how the powertrain behaves after prolonged use. At the proving ground, however, a vehicle can repeatedly drive up a steep gradient, pull away and brake. This subjects the powertrain to demanding operating conditions that accelerate component wear – significantly reducing the time required for durability testing.

How the Gradient Test Roads Were Built
During construction, we made use of the original military vehicle handling area. Measurements showed that the concrete panels had sufficient load-bearing capacity for the new use. We then added successive layers of material, stabilised them with cement and lime, compacted them and shaped them to form the final profile. Geogrids were also incorporated into the structure to reinforce the side slopes, allowing them to reach angles of up to 45 degrees.
“The original plan was to use asphalt surfaces. However, this is not feasible on gradients above 20%. Both the paving process and compaction technology impose limitations. We therefore opted for concrete, which can be formed even on extremely steep gradients,” explains Zdeněk Svoboda, Head of the AUREL Proving Ground. The structure therefore consists of crushed aggregate, cement-bound aggregate and a cement concrete surface. Asphalt is used on the sections between the individual gradients.
The World’s Only Polished Basalt Low-Friction Surface
The 15% gradient features a unique facility found nowhere else in the world – a polished basalt low-friction surface wetted with water. Its location on this particular gradient reflects the requirements of certain vehicle manufacturers’ test standards.
Development teams use the surface to test braking systems and drivetrain components, such as differentials, and assess their durability. The low-friction surface can also partially replace certain tests that would otherwise need to be carried out in winter conditions, for example in Nordic countries. To keep it operational during the winter, we equipped it with an electric heating system that helps prevent ice build-up.

For Development and Driver Training
Gradient test roads are used not only by vehicle manufacturers for testing motorcycles, passenger cars, commercial vehicles and special-purpose vehicles – they also play an important role in corporate events and driver training. Participants can practise hill starts in both cars and on motorcycles or experience driving on the extreme 65% gradient. Due to its demanding nature, however, the 65% gradient is restricted to drivers who have completed the highest level of AUREL Proving Ground training. Restrictions also apply to vehicles with limited approach and departure angles, as their front or rear bumpers could make contact with the surface at the sharp transition.
We use the rear sections of the gradient test roads for side-slope driving, particularly when testing ambulances.
All gradient test roads are designed for year-round operation, 24 hours a day, 7 days a week. The entire test area, including the access road, is illuminated, and we regularly maintain the surrounding vegetation and clear snow and ice. Water also drains naturally from the steeper gradients, reducing the formation of ice.
Do you need to test brakes, the drivetrain or other vehicle systems under repeatable conditions? Get in touch. Together, we will develop a test scenario tailored to the needs of your project.



