The answer to this question shapes the entire development cycle of a modern vehicle. A skid is neither a random vehicle fault nor simply the result of driver error. It is a precisely defined state in which the tyre can no longer transmit the required combination of longitudinal and lateral forces. The transition from adhesion to macroscopic sliding provides development engineers with particularly valuable data. AUREL covers the entire process – from virtual calculations, simulations and measurements through physical testing at the proving ground to the design of specific technical solutions.
The Friction Ellipse in Practice
Losing grip is not merely a critical situation. In automotive engineering, it is a moment of truth that brings together tyre physics, chassis dynamics, sensors, software and the experience of the test driver. Evaluating all these factors together enables further advances in the safety and development of today’s vehicles, where understanding vehicle behaviour at the limit of adhesion is more important than ever.
The tyre’s grip limit determines the resultant combination of longitudinal and lateral forces that can be transmitted through the contact patch. If the demand for longitudinal and lateral force exceeds this limit, the tyre loses grip. The vehicle may then transition into understeer, where the front axle deviates from the intended cornering path, or oversteer, where the vehicle begins to rotate about its vertical axis.
Guardian Angels in Action
Situations at the limit of adhesion are managed with the help of ABS, ASR and ESP systems, which selectively brake individual wheels to correct the vehicle’s direction of travel and maintain stability. In modern vehicles based on SDV (Software-Defined Vehicle) architectures, these systems no longer operate in isolation. They form part of complex control architectures that fuse data from inertial sensors, cameras, radar and LiDAR.
The aim is not to intervene as early as possible, but at the right moment and with the appropriate intensity, allowing the electronic systems to work naturally with the vehicle’s chassis dynamics. This is why thorough validation is essential before the software is deployed in a production vehicle. In Software-in-the-Loop (SiL) and Hardware-in-the-Loop (Hile) environments, a digital twin can be used to simulate thousands of loss-of-grip scenarios without the risk of damaging physical hardware.

AUREL Proving Ground: From Virtual Reality to the Test Track
The next stage is Vehicle-in-the-Loop (ViL), where a physical vehicle drives around the proving ground while its sensors receive virtual data about surrounding traffic and obstacles. This allows development engineers to simultaneously monitor the chassis response to skidding and the behaviour of the control algorithms, and to fine-tune the systems so that they are effective while still feeling natural to the driver.
While skidding is difficult to predict on public roads, at the AUREL Proving Ground development and innovation centre it becomes a controlled and repeatable experiment. The 120,000 m² facility features a 76 × 8 metre polished basalt low-friction surface, continuously wetted with water. Under precisely defined conditions, engineers can induce both understeer and oversteer and monitor their effects on vehicle behaviour.
Repeatability is essential in vehicle development – when comparing different calibrations, engineers need to be certain that differences in results are caused by technical changes rather than variations in track conditions. The AUREL Proving Ground also features a water channel with a depth of up to 55 cm, Belgian block and washboard sections for testing sensor durability, as well as additional tracks for dynamic testing. Test teams can therefore carry out consecutive tests without leaving the facility.
Advanced Sensors and Strain Measurement: Hard Data Instead of Impressions
The test driver’s subjective assessment is important when evaluating steering feel, but objective data is essential for engineering development. AUREL therefore uses advanced strain measurement, with sensors installed on the chassis, suspension arms and steering knuckles to monitor material microstrain in real time. From these measurements, engineers determine tensile, compressive and bending stresses and monitor changes in individual wheel loads, dynamic weight transfer and the onset of lateral acceleration.
The measured telemetry data are used to validate CAE models and reveal differences between simulation and the actual vehicle, such as the effects of suspension bush compliance or the track surface. This is complemented by 3D optical analysis using photogrammetry and precision scanners, which makes it possible to identify and assess any permanent plastic deformation of components following extreme loading.

Type Approval and Vehicle Testing Beyond Normal Use
Vehicle development does not end with fine-tuning its driving characteristics. A vehicle must also withstand conditions beyond normal use and meet stringent safety requirements. At its proving ground, AUREL therefore conducts misuse testing – including kerb strikes, jumps, driving through deep potholes and crossing railway sleepers. These tests verify the durability of the chassis and the correct operation of restraint systems under extreme mechanical loads.
AUREL also specialises in certified passive safety and pedestrian protection testing. At the only Pedestrian Protection Testing Laboratory in the Czech Republic, testing is carried out in accordance with Euro NCAP protocols and UNECE regulations.
From Measurement to Specific Technical Solutions for OEMs
Based on the measured data, AUREL recommends specific modifications to vehicle manufacturers, covering the chassis, driver assistance systems and their mutual calibration. The measurement results are complemented by the experience of test drivers. The aim is not merely to describe vehicle behaviour in limit situations, but to identify specific technical solutions for further development.
AUREL’s comprehensive services cover the entire process – from virtual calculations, simulations and measurements through to physical testing at the proving ground. By bringing all the necessary stages of development under one roof, AUREL is a long-term partner to leading OEMs and suppliers.
AUREL also offers skid training, professional training courses, corporate events and tailor-made team-building events, where participants can experience, under controlled conditions, how a vehicle behaves when it loses grip.
Test your vehicles at the limits of their performance. AUREL offers vehicle manufacturers comprehensive services – specialist measurements, simulations and testing at the AUREL Proving Ground.



